Home > Power Supply > Power Supply Woes

Power Supply Woes

You could still get a few more years of reliable use before something starts to act up on an irregular basis. These capacitors are like small storage devices like batteries that remove any voltage ripple components from the mains AC or the switching frequency. It operates at 60 Hz. Here in the U.S., the typical line voltage is 110 to 125 volts. http://macland.net/power-supply/power-supply-atx-2-0-any-suggestions-as-to-a-power-supply.php

The ones we are concerned about in your ESQ1 are about 3/4 inch (2 cm) in diameter and 1 inch (2.5 cm) tall. here is the real kicker, you can create a TNF, eliminate the noise, then 5 minutes later the peak has moved.. I think I will go with dust's information, that looks exactly like the one I need. Reply With Quote Sun 4th Sep 2016,16:51 #4 K5XOM View Profile View Forum Posts Private Message Join Date May 2011 Posts 198 Thank you for the replies.

Its not worth destroying your ESQ1 by attempting to do it yourself. The failed cap may have caused other problems, so replacing the cap alone is no guarantee that the problem will be fixed. It is the one part of any piece of equipment that has to work the hardest. All Rights Reserved.

Neil Kolban Tech Thoughts on computing and technology … Menu Skip to content Home Breadboard power supply woes I have been using a breadboard power supply for

The higher input voltage overcomes the power supplies ability to regulate. But even though it is getting that, there is no power coming from the 12v sides??! I've seen traveling musical groups take along a voltmeter to monitor their voltage so they can eliminate mains power as their problem in troubleshooting their musical equipment problems. Community enhanced support for FlexRadio Systems New Post Search Community Home Categories About FlexRadio Systems Home Categories About New Post Go Sign In Register Community Home Products: SmartSDR for Windows FLEX

As a preventive measure, all the large capacitors in the power supply should be replaced at least once in the lifetime of the ESQ1. Look them up and check out the reviews as well. They are very efficient sometimes reaching 85% or more. http://www.neatcircuits.com/ensoniq/pswoes.htm The system returned: (22) Invalid argument The remote host or network may be down.

The psu works fine, shorted out there, but I am wary that that might blow something else up if it runs like that. In the next part, we’ll take a look at Century Aluminum’s outlook. {"metrics":["Open"],"tickers":["ATI","AA","CENX","XLB","IGE"],"ticker_names":["Allegheny Technologies Incorporated","Alcoa Inc.","Century Aluminum Co","Materials Select Sector SPDR","iShares S&P NA Nat. A bad connector or low-percentage braid cable can let a lot of junk into the system (and out).Brute force line filtering on pool pumps can help. Like Comment 0 people like this Submit Cancel 1 year ago Walt - KZ1F 2999 Posts 635 Reply Likes That's so weird, your spikes appear evenly spaced every 6khz on 40m.

I just blew the dust out of my computer with an air compressor. Like 0 2016-02-04T23:58:56+00:00 Gerald - K5SDR, Official Rep 550 Posts 891 Reply Likes Make sure you use type 31 ferrite material toroids.  If you don't know what the material is, it Over that period they can and will deteriorate (change capacity value) and loose their ability to hold a charge. The SEC 1235M crashed on, and the internal 8 amp fuse blew.

Alcoa currently forms 0.89% of the iShares North American Natural Resources ETF (IGE) and 2.8% of the Materials Select Sector SPDR ETF (XLB). http://macland.net/power-supply/power-flashes-when-i-flip-the-power-supply-switch.php Like 0 2016-02-05T01:36:41+00:00 David Warnberg 429 Posts 36 Reply Likes Walt, if you look at my post it's the solar pool pump, there are attached pictures to show it.. Reply Quote Nate523 Re: Power Supply Woes March 11, 2016 01:14PM Registered: 11 months ago Posts: 66 Toroidal inductor is that copper wired thing isn't it? I got one from radioshack that was blue, it doesn't work.

It is also sold under a few different brand names, as are a lot of amateur accessories. Speaking yesterday in Lilongwe on the sidelines of a national validation workshop on energy policy he said some of the interventions include purchasing and installing diesel-powered generators by Electricity Supply Corporation If you know which end of a soldering iron to hold, you may be able to replace the dead cap- they usually aren't hard to spot. Check This Out C1 (3300uf/25v), C8( 3300uf/25v), C17(4700uf/16v), C18(4700uf/16v).

I have the S400-12 36A unit. It is suppose to continuously handle 25 amp load, but personally I am skeptical about that because I wasn't pushing it. it worked flawlessly until today.

there are other birdies there and I've found that to be the power supply for the most part....David Like 0 Submit Cancel 1 year ago KC2QMA 302 Posts 60 Reply Likes

That being said, for noise, you can't beat a well-regulated linear supply. Read the photo below. Reply Quote Nate523 Re: Power Supply Woes March 13, 2016 03:34PM Registered: 11 months ago Posts: 66 Unfortunately no, it has ntc on the top I know that, generally know the capacitors arrived and I changed them out, but they did not cure the power supply.

We all learned simple calculations in high school physics. Since the demand for current is somewhat higher than the 5 volt regulator can provide, two 51 ohm resistors are shunted across the regulator to "cheat" a little and take some It is amazing to see this number change from hour to hour, from day to day, and from season to season. this contact form As week as the radio,this also powers my: SWR meter, my satellite receiver clock, my aerial switcher, my MFJ intellituner, and my desk lighting.

I connect the equipment to the battery side of the power gate Like 0 Submit Cancel 1 year ago KC2QMA 302 Posts 60 Reply Likes I agree Linear PS are the They are a little pricier than the Astron ($155 vs $130), but well worth it in my opinion. 73, Ray, K9DUR Like Comment 0 people like this 2016-02-04T15:25:11+00:00 David Warnberg 429 Reply With Quote Sun 4th Sep 2016,19:36 #6 WA9WVX View Profile View Forum Posts Private Message Join Date Dec 2008 Location Elgin, Illinois Posts 1,507 Hello Ken, Back in the early The main board requires 5 volts for the digital logic and + and - 12 volts for the analog (audio) circuits.

I don't know if this is necessary, but my computer is an older eMachines. It hasn’t yet reached an agreement at its Hawesville plant.