Home > Power Supply > Power Supply Questions

Power Supply Questions

Contents

How do I measure ripple and noise? Spend a few moments of time with your class to review some of the “rules” for building circuits before they begin. One popular type puts out 13.8 volts DC and is intended to provide DC power to devices normally powered from an automobile battery. A mobile cart containing a computer, printer, and scanner gets +12, -12, +5, and +3.3 V directly from the UPS for the computer, printer, and scanner, and the monitor gets 120VAC have a peek here

The falcon 16 allows you to set in the controller and then use the default RGB output from xlights. I don't want to use any prebuilt chips where you have a magic black box with inductors, capacitors and resistors connected to it. The above regulation specifications are steady state behavior. Learning to mathematically analyze circuits requires much study and practice.

Power Supply Test Questions

Such an answer is misleading, since it completely ignores polyphase AC rectification! Types of DC Power Supplies Battery Eliminator Illustration 1: B&K Precision model 1502 These types of supplies tend to be the least expensive. A Zener voltage regulator will cease to act as a voltage regulator if Zener current becomes …………… Less than load current Zero More than load current None of the above Answer Ask !

The group's new production facility in Vietnam is the most energy efficient power converter factory anywhere in the world. I also read somewhere that lower switching speeds are more efficient. Remains the same Decrease Increases None of the above Answer : 3 Q14. Question 21 Power supplies are sometimes equipped with EMI/RFI filters on their inputs, to prevent high-frequency “noise” voltage created within the power supply circuit from getting back to the power source

Has copy protection ever been used in physical books? The rupture of co-valent bonds will occur when the electric field is …………. 100 V/cm 6 V/cm 1000 V/cm More than 105 V/cm Answer : 4 Q11. Reveal answer Hide answer Any one diode fails open: Half-wave rectification rather than full-wave, less DC voltage across load, more ripple (AC) voltage across load. Typically stated as a percentage of the total voltage or current available from the supply.

In our country, the standard voltage in houses is 220V AC. But I was able to run over 330 pixels in test mode before a 5v 5a power supply started getting hot. Revenues are approximately split North America 50%, Europe 42% and Asia 8%. Commercial power supplies have voltage regulation ………….

  1. Reveal answer Hide answer A low pass filter is the kind needed to filter “ripple voltage” from the power supply output.
  2. It then switches on it's inverter (the part that produces output alternating current from it's inverter) and supplies output power from the battery or batteries until the mains voltage has been
  3. A lower frequency limit is 25 kHz (to stay above the human hearing range) and the state-of-the-art upper limit is currently around 3 MHz.
  4. There are two basic types of UPS in modern use.
  5. It monitors the line constantly for a major voltage drop that signifies power failure.
  6. Why does Warren Buffett say his fund performance, relatively, is likely to be better in a bear market than in a bull market?

Objective Question On Smps

How to temporarily mark a trail? http://www.powerstream.com/q_a.html Battery life is halved for every 10 degrees (C) temperature increase above it's specified operating temperature (usually 25 degrees (C). Power Supply Test Questions You'd do well to look at the internals of the "black boxes" you decry, because you will learn how to do it properly. -max- (author)  steveastrouk3 years agoReplyI have a few Mcq On Ups The basic behavior of the supply is to maintain the voltage you have set regardless of the load's resistance.

Question 27 Calculate the approximate DC output voltage of this power supply when it is not loaded: Reveal answer Hide answer Vout ≈ 11.6 volts Notes: Ask your students to navigate here The linear regulation strategy has advantages of simplicity, low noise, fast response time, and excellent regulation. The simple "series" model of a capacitor or an inductor places the pure reactance in series with a pure resistor, whose value is usually called the ESR. One output supplies 0 to 6 volts, intended for digital logic. Indiabix

Unless you take your PC abroad don't touch it. I recommend projecting an image of a bridge rectifier circuit on a whiteboard, then having students use dry-erase markers to “mark up” the schematic with arrows for current, voltage drop indications, Input Voltage range:. . . .7-24 Volts Voltage:. . . . . . . . . . . . . . 5-24 Volts Max Current:. . . . . . . Check This Out Reveal answer Hide answer The problem is that the vertical axis input is DC-coupled.

Blue field:This module will be fed the triangle wave, decrease it's amplitude, and inject it with a bias voltage, controled by the current limiter (red field). Be as specific as you can in your answers, identifying both the circuit element and the type of fault. Where should the line be drawn regarding political statements in a scientific report?

A problem of the typical linear power supply is the size and weight of the transformer.

Because of this, switching mode power supplies often have a minimum output voltage specification. Peak inductor currents exceed the mean inductor current by some margin. This is a very time-intensive and inefficient method of troubleshooting. It can be important to know what bandwidth the noise is specified over.

As the battery becomes charged, and its voltage approaches 13.8 volts, its load decreases to the point where it no longer demands the full 1 amp charging rate. What is true about the breakdown voltage in a Zener diode? The best approach is probably to use a non-inductive current shunt for the current measurement and two independent differential amplifiers to measure the AC input voltage to the power supply and http://macland.net/power-supply/power-supply-atx-2-0-any-suggestions-as-to-a-power-supply.php For increasing the voltage rating, zeners are connected in …………..

Follow-up question: explain in detail how the issue of non-isolation could create a safety hazard if this rectifier circuit were energized by an earth-grounded AC line circuit. Similarly, crossover from the constant current to the constant voltage mode automatically occurs from a decrease in load. We also have a much larger standard product portfolio than our competitors which gives us an advantage when customers are choosing preferred suppliers as we are more likely to have a by Mark W.

Home/Support/Downloads (Software, Images, Guides, etc..)/Power Supply Guide Languages B&K Japan (日本語) B+K Taiwan (繁體中文) B&K (en Español) B&K (em Português) Sefram (Français) B&K Precision Corporation © 2017 News & Media Contact The 115V and 230v switch is to allow the PSU to handle different voltages used in the USA vs. steveastrouk -max-3 years agoReplyNo, HIGHER switching speeds, done right, are much more efficient, components are smaller, emissions lower. Q.

It is usually implied or assumed that the power supply is tested at a constant load with no AC line variation. In the occurrence of a blackout, for example, your computer would continue to draw power from the UPS thus allowing you to save your work and shutdown your system properly without Regulation Load regulation is how much the output voltage changes when the load changes, usually from 0 to 100% of rating. Typically, students practice by working through lots of sample problems and checking their answers against those provided by the textbook or the instructor.

Note: sometimes ripple and noise is specified as PARD, which is an acronym for "periodic and random deviations". Include the cost of yearly calibrations and any estimated losses due to unavailability or having to repair or replace the unit if it fails. These measurements assume a 100% linear pot, and (close enough) to ideal op-amps.