Home > Power Supply > Power Supply? (newb Question)

Power Supply? (newb Question)

Hot Network Questions Find Recursively Prime Primes How this actually update where there is no change in record? If I were looking toward the future I would run cable with the extra wire (usually red) that would allow upgrade to 240 volt and deadhead the red wire until needed. Not as likely and only if, once again, the run from the panel to the welder is long. So if you want to put a longer cord from the welder to the plug going to #10 may be the thing to do and it won't hurt anything and you have a peek here

Use this tag if you need further help sourcing electronic components or parts related to a circuit build or repair. Examples below. If a matrix commutes with a set of other matrices, what conclusions can be drawn? If it is +12V 1A rated it means it can deliver 12Watt, so you have more than enough power. hop over to this website

For general hookup, power and usage advice, and all questions on IDEs and general programming, with pre-built assemblies (eg: Connecting I/O or power modules to Arduino, Raspberry Pi, ESP8266 etc.), try Picture below EDIT - datasheet: http://www.omc-stepperonline.com/download/pdf/S-350-60.pdf current safety share|improve this question edited Oct 24 '16 at 22:35 asked Oct 24 '16 at 18:13 JDS 518514 add a comment| 1 Answer 1 To Get More Info and Daily Reward.

  1. Custom 112 cab W/G12 75T.
  2. Reply With Quote Quick Navigation The Guitar Shop Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums The Pickup Lounge The Guitar Shop Amplifier Central The
  3. It would be cheaper to use a 20A breaker and your 20A plugs with the #10 wire if you go this route since the welder should only draw its max rated
  4. Please read the Wiki/FAQ before submitting a question.

You can also add a flair tag for your username with your area of expertise by clicking on the "edit" button at the top. Built by passion, perfected by obsession. Thanks for trying to help me. I have an MXR Dyna Comp and a Korg DT10 but I can't figure out which 9v power supplies to buy to run these pedals.

Not the answer you're looking for? You can buy one, and use a daisy chain like this to connect several effects to a single power supply: Join me in the fight against muscular atrophy! Just trying to remove any barrier to getting as much as I can out of what I have... picking component values).

You plug lamps requiring 0.5A (60W) into 15A circuits all the time.2. Last edited by deolexrex; 11-22-2013 at 04:53 AM. Avoid giant player classes Does this self-assignment do something sensible? Thank you.

So, as I'm putting together my electric rig I'm stumped. news Related subreddits Electronics Design - specialist subreddits Constructing your own audio gear - /r/diysound (active moderation) and/or /r/diyaudio (no moderation) PCB design - /r/PrintedCircuitBoard Signal processing - /r/DSP General Broader ECE In other words, can I hurt the welder by plugging it in to a circuit capable of providing 30A @ 120.2) Given that the welder performs much better on a 20A Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the

There is no reason not to feed # 10 wire from a 20 amp breaker if you are looking toward a future upgrade. navigate here Login Register 22-February-17, 11:34:47 Welcome, Guest Please login or register. The machine should have ratings on a label on the back, just check them out and size accordingly. Why do model aircraft fly and maneuver so differently from real aircraft?

Ideally, they are the same but if your supply wire, both within the wall and from the plug to the welder, are too light you will have a voltage drop along Logged I only take responsibility for what I say, not for what you understand. It also says there is a breaker in the machine and also thermal protection. Check This Out If you have a general technical, setup or purchasing question on any electrical or electronic product (except for items covered by the 'Equipment' tag), please use /r/techsupport, /r/electricians or a subreddit

Browse other questions tagged power or ask your own question. Thanks power share|improve this question asked Jan 23 '15 at 18:17 Andrew Simpson 1012 marked as duplicate by Ricardo, Nick Alexeev♦ Jan 23 '15 at 19:00 This question has been asked Why is x**4.0 faster than x**4?

Fewest (distinct) characters for Turing Completeness What does CWOP mean on visa cancelled stamp?

I am a hobbyist welder - mostly on cars etc. Thus you will get very little advantage from oversizing the circuit since the machines own protection will fault out if the input exceeds that expected. Jan 23 '15 at 18:25 It just blew up! {joke joke} Thanks that worked –Andrew Simpson Jan 23 '15 at 18:26 add a comment| Not the answer you're looking By billvanderhoof Date 01-17-2006 08:06 http://content.lincolnelectric.com//pdfs/products/navigator/im/IM724.pdfIf you don't have it that link will get you an operator manual.

Again I really appreciate your help. Efficient counting I have sole custody of my child but the child's father's brother claimed him as a tax deduction Almost totally distinct functions A phrases that basically means 'walk your Logged I only take responsibility for what I say, not for what you understand. http://macland.net/power-supply/power-supply-5v-question.php Check below for guidance on where to post those types of questions.