Home > Hard Drive > Problem WIth Hard Drive/ Cd Drive/ Ide Lead

Problem WIth Hard Drive/ Cd Drive/ Ide Lead

Contents

The Drive reads fine at times but other times it does not work correctly. 1) Check the CD-ROM disks for scratches and fingerprints. leroys1000, Jun 20, 2009 #2 Frank4d Trusted Advisor Joined: Sep 10, 2006 Messages: 9,126 Also note if the IDE cable has blue, grey and black connectors, the blue one plugs into Make sure the activity LED is lighting up on the drive you put the disc in when you try to read it. When installing the CD-ROM drive, you need to know what other devices are connected on that IDE cable. this content

This is supposed to happen, don't worry. In this chapter, we'll help you find the reasons for hard disk problems, find the solutions, and show you how to get advance notice of problems before a sick hard disk If that happens to be your collection of MP3 or WMA CD rips, it's going to be very quiet at your home or office until you get that hard disk back Frankly, when I need a paperweight, a nicely polished rock works a lot better--and it's easier to lift besides!

Ide Hard Drive Jumper Settings

now i need to use the cd drive, i have put the cd drive on " slave" and got a slave lead, so i plugged the ide lead into the motherboard, Does CD-R slow down hard drive on same cable? If you want to make it the master or the slave, you will have to look around the drive to find where the instructions are. Return to Diagnostic Chart Does the BIOS report the transfer mode correctly for older PATA drives, like UDMA/100 or ATA/66?

Installing in OS/2 Try selecting the "non-listed" IDE CD option in OS/2 Warp. Checking the Hard Disk Connection to the Power Supply 172 I just installed a new ATA/IDE drive, and the screen is blank when I turn on the computer. Assign the drive letter. How Many Ide Controllers Are Available On Most Motherboards The boot hard drive should always be the Master on the primary IDE interface.

Try the disc in another reader before chucking it out, it could just have trouble with the device you were trying it in. Return to Diagnostic Chart SMART is one of those cute acronyms you don't want to see popping up on your screen with a nasty message. Retail stores also sell cables with multiple connectors on each end making it easier to match the connector to the device. her latest blog If the CD-ROM is on the end of the chain then make the termination active.

When i put both on the cable, the dvd drive opened which means it must be working...but the hard drive wouldnt work and a message came up saying no OS boot Using A ____ Driver Will Help Prevent A Computer From Being Compromised. If not, you can try a 3rd party data recovery tool or send the drive out for data recovery if it's critical. If the motherboard won't register any drive you attach, even on new cables, and if those drives are spinning up, it indicates that either the IDE controller is bad or all DVD Media Compatibility 684 I installed Y-splitters to power additional drives, and now I'm having problems.

  1. The SSD firmware controls the relatively high burden of housekeeping tasks that the SSD drive must perform independently of the PC, especially wear leveling and other tasks that will extend the
  2. This chapter is from the book  This chapter is from the book Leo Laporte's PC Help Desk Learn More Buy This chapter is from the book This chapter is from
  3. Attach cables The CD-ROM should have two cables connected to it and may have an audio cable, which is the smallest of the cables, the CD-ROM audio cable (or sound card
  4. If the tray still doesn't eject, reboot again and note whether the BIOS registers the drive.
  5. Return to Diagnostic Chart Have you updated the firmware for your SSD drive?
  6. The connectors aren't soldered to the wires, the circuit is made mechanically with "V" shaped contacts forced through the plastic and digging into the conductors.

How Many Hard Drives Can Be Connected To A Single Ide Cable

This means is it's possible for a laser failure or one dirty lens to lead to a drive that can play one generation of media and not another. https://forums.techguy.org/threads/problem-with-hard-drive-cd-drive-ide-lead.836819/ If for some reason the computer chose a drive name that is already in use by another device or if you want the drive to have a different drive letter you Ide Hard Drive Jumper Settings Is the full capacity of the hard drive being seen: Verify the BIOS has auto-detected and LBA mode is enabled. How To Connect Two Sata Hard Disk In One Pc Don't keep running a drive that vibrates badly even if it plays discs.

ATA/IDE Disk Drive and Device Troubleshooting 679 I can't read optical media. news Volume label is nothing other than the name you want it to be called. Return to Diagnostic Chart The diagnostic tree splits here between the newer SATA (Serial ATA) interface drives and the older PATA (Parallel ATA) interface drives. Open up your computer case. What Happens When The Data Cable To A Floppy Drive Is Not Connected Properly?

Partitioning the drive in Windows If you install a new drive and want to use it in Windows, you must partition the hard drive first! Return to Diagnostic Chart Computer Repair | Power Supply | Video Card | Motherboard/CPU/RAM | Hard Drives | CD and DVD | Sound Card | Modems | Networks | Foner Books Write down important information from the top or bottom of the CD-ROM such as the Model Number, Serial Number, and specifications. http://macland.net/hard-drive/problem-with-2nd-hard-drive.php If your drive reads data, plays movies and music, boots bootable discs, and doesn't vibrate or make noise, it's likely a PC performance problem is degrading the playback.

Verify that the location that you are connecting this cable to is NOT the jumpers on the back of the drive; while it may be possible for the cable to connect How To Connect Dvd Drive To Motherboard Sata Frank4d, Jun 20, 2009 #3 This thread has been Locked and is not open to further replies. Note also that in two drive systems, the builder may only have patched the audio output of one of the drives through to the sound card.

If not, select the auto-detect option.

Required fields are marked *Comment Name * Email * James Bruce 631 articles James lives in the middle of nowhere with his wife, son, and chickens. Master with non-ATA compatible drive - Use this if the drive is Master to a CD-ROM, tape drive or other non-ATA drive. You should be able to remove a jumper with your finger nails, if not then use a pair of very small needle nose pliers and don’t bend the pins. Ide To Sata Converter All Rights Reserved.

Return to Diagnostic Chart Does the drive play CDs but not DVDs or DVDs but not CDs? If you have an older drive please visit our Technical Library and find your model number for details on jumper configuration. And there are some ways to partition the hard drive actually, say, partition the hard drive under Disk Management or use the third party partition manager tool like EaseUS partition Master check my blog If the faceplate seems to be bulging as you pull, the disc is hung up on it, and the best thing to do is remove the drive from the PC and

There are two distinct places that might need to be changed. 1) If the drive is installed on a secondary IDE controller, then you will need to go into the BIOS Erasing CD-RW Media Created with Windows XP's CD-Writing Wizard 231 I want to upgrade the hard disk in my portable computer to a larger, faster drive. Normally it's red on the grey cables and white on black cables etc there will be some kind of colored line to indicate pin 1. PC Advisor Phones Smartphone reviews Best smartphones Smartphone tips Smartphone buying advice Smartphone deals Laptops Laptops reviews Laptops tips Best laptops Laptops buying advice Tablets Tablet reviews Best tablets Tablet tips

Cable-Select Option (Default) - Use with Ultra ATA cables. Works fine when its on its own without the HDD. ide harddrive and cdrom on same cable...It's slow so I sold them a recertified 500gig for 30$...