Home > Hard Drive > Problem With 2nd Hard Drive

Problem With 2nd Hard Drive

Contents

You Might Like Shop Tech Products at Amazon PCWorld PCWorld helps I presume that this is due to XP If it is, MS deserve a k*ck up the backside!!! Do it on both sides of the memory." This worked for me. Report shihadchick- Jan 3, 2009 at 09:55 PM Just wanted to say thanks a bunch - I'd been going nuts with the same problem and having that laid out clearly helped check over here

Any help greatelt appreciated!! Moving along the edge of the grate, lift a perforation with the hook to help it slip into place. I am still unable to get a solution from anybody. But I cannot get my second Western Digitial EIDE Hard Drive recognized. http://ccm.net/forum/affich-26671-second-hard-drive-not-recognized

Windows 10 Not Detecting Second Hard Drive

Computer systems are still way too complicated for the average user! If the second hard drive cable is placed on top of the first, the antenna plate will not reattach, and you could damage your cable. 10 comments When re-installing the original After reassembly, boot the Mini into Lion Recovery and use disk utility to erase your SSD. arrow-left_smallBackMac Mini Late 2012 Repair Full Screenfull-screen_large Optionsmore-vertical_large History Save to Favorites Download PDF Edit Translate Get Shareable Link Embed This Guide Notify Me of Changes Tools Buy these tools Mac

When inserting the hard drive, be sure to place it in its bracket cable side up with the SATA connector closest to the bulge in the bracket seen in the third Then install Lion on your SSD. I have put it in and taken it out several times and everytime it is in there it won't shut down properly but it never happens when it's not in there. Second Hard Drive Not Showing Windows 10 Now Im installing the system in the ssd and I will format the HD.

Thanks Have you tried installing the 2nd HDD and going into the BIOS and reset it to factory defaults? Second Hard Drive Not Showing Up In Disk Management I had a Seagate 1TB and a 2TB WD Green. mattgarfield - 10/05/2014 Reply On re-assembly, when you're putting the HD back in place, before you've pushed the logic board fully back into place, make sure the disk is in the anonymous 3693 - 04/27/2013 You can leave the antenna plate attached and remove the logic board if you're careful while removing the motherboard.

I suggest the following additions: "The tool acts as a lever. Installed New Hard Drive And It Wont Boot Not reading carefully enough, I accidentally removed the whole socket from the board. Tried many times to switch cables into but any order i try is not the good one. Leave your dvdrom drive out for the time being.

  1. Lucky for me, they came out clean and I was able to just re-insert them into the connector Kyle Jurick - 12/03/2013 Reply On a Mini bought Jan 2014, Red screws
  2. cegondaireun - 12/22/2013 Reply Uhh I can't get this to go back in?
  3. Christer - 02/16/2014 Reply I have been using my mid-2011 Mac Mini as a media player while working/living oversees.
  4. Open it up, copy your old files that you need (songs, pictures, documents...) to your new drive.

Second Hard Drive Not Showing Up In Disk Management

In that case, shut down the PC, open it up, and make sure everything is properly connected. try here But I definitely need to buy a new PSU!!! Windows 10 Not Detecting Second Hard Drive But Windows doesn't see it. [Email your tech questions to [email protected]] Before we discuss your problem, let's consider why you would want a second hard drive in your PC. Computer Won't Boot With Second Hard Drive After insuring that the screws all lined up, I installed and tightened the logic board, then the other antenna plate screws.

If the power harness is next to the power supply, go back and re-route it properly. http://macland.net/hard-drive/problem-with-hard-drive-priority.php Cheers. Hope you can go around with that. This will help the cable attach and stay in-place. Computer Won't Power On With Hard Drive Plugged In

Perhaps drinking half a fifth of whiskey before starting this project was unwise. JiaJing WANG - 01/15/2014 Reply Hi You are right, install an ssd in the upper position make the mini think that a Fusion drive is installed and try to configure itself aeternum91Feb 7, 2014, 5:41 PM artart00 said: Hi aeternum91,In my case it really ended up being the power supply. http://macland.net/hard-drive/problem-with-new-maxtor-hard-drive.php This process got stuck the 3 times I tried.

Subscribe ▲ Learn more about PCWorld's Digital Editions    🔎 Home News Reviews How-To Video Business Laptops Tablets Phones Hardware Security Software Gadgets Subscribe Resources PCs Phones Printers Ultrabooks Installed A New Hard Drive Now Computer Won't Turn On or is it necessary to flip them? I want to install it as a slave drive in my comp.

If not, check that the power harness from the power supply is routed correctly.

Your +12V is normally split between what called rails, And the +12V rail you are using is just not enough for the 2 HDDs and what ever else is on the Hope you can go around with that. Using the antenna plate as a handle, I was able to guide the SSD into the hard drive mount. Windows 10 Not Recognizing External Hard Drive Moldyjohn - January 19 Reply Add a comment Add Comment 1024 Step 14 Edit Remove the following three screws: One 5.0 mm T8 Torx or 2.0 mm Hex screw (either screwdriver

Generally, soon after you turn on the PC, well before Windows loads, a message similar to “Press F2 for Setup” flashes onscreen. Make sense? Don't worry: it's only 20 steps to get back to it. have a peek at these guys Please note, the second HDD did not contain any OS, and I was using it for storage of excess data only.Recently, I tried booting the system and like you I faced

There Needs to be a closed circuit so u will need something on one of the 12 volt rails that HAS THE ABILITY to run at 12v. I too had to remove the standoff screw. Repeat the process for the remaining three grommets on either sides of the brackets. 4 comments The spudger is very handy at this point.